hohner

    Hohner Automation Ltd.


Home Email Distributors Terms About Us Accessories Download 3D AutoCAD

Series 14 incremental hollow shaft encoder up to 40 mm

(non intrinsically safe part number)

 


1   4 X X   X X   X   X / X X X X
|_______| |_______| | | R  E  S  O  L  U  T  I  O  N
Shaft Size Output Signal | Connection Up to 3000 ppr max
Output Circuit

 

XX

Shaft Size

XX Output Signal

12 = 12 mm

31 = channel A
14 = 14 mm 32 = channel A and B
25 = 25 mm 33 = channel A, B and O
40 = 40 mm.......you get the picture..... 34 = channel A and A comp
AA = 1" 35 = channel A & B and A & B comp
OA = 5/8" 36 = all six channels
OB = 3/4"
OC = 7/8"
OD = 1 - 1/8"
X Output Circuit X Connection
2 = 5V TTL 4 = 9512, 12 pin plug & socket
7 = Current Sink / Open Collector 5-24 V D = 9 pole D
9 = Extended Line Driver 5-24 V R = 2 m cable attached to 9 pin D
  F = 3 m cable attached to 9 pin D
H = 4 m cable attached to 9 pin D
J = 5 m cable attached to 9 pin D
L = 8 m cable attached to 9 pin D

Technical Data Connection Options
Operating temp: - 20 ...+   60 degrees C 9 pole Cable 12 pin
-   4 ...+ 140 degrees F PS GND 1 Black 1
On request: -20 ... + 80 degrees C PS 5 ... 24 V 2 Red 2
Max frequency: 150 kHz Output A 3 White 3
Current consumption: 90 mA (max.) Output B 4 Blue 4
Power supply: 5 - 24V Output O 5 Yellow 5
Weight:    21 oz (0.6 kg) Output A inv 6 Green 6
Protection: IP 64S, NEMA 3 Output B inv 7 Violet 7
Housing: Aluminum Output O inv 8 Brown 8
Shaft: Aluminum
Bearings: 2 x 6810 ZZ C2 Output
Torque: 0.4 oz/in (3 N-cm) Diagram is shown with clockwise shaft rotation viewed from 
Humidity: Up to 98% permissible

opposite side to shaft grub screws

Speed:  3000 RPM max.
Shock: 10g (6msec)
Vibration: 5g (500 Hz)
Shaft load: Supports its own weight
Line driver output max: 50 mA per channel
Max. ppr 3000

Mounting Instructions
Mount fixture to the machine with three screws and three washers, M6 or 1/4".  Slide the encoder onto the shaft.  With the setscrews, tighten the hollow shaft encoder onto the shaft with a minimum clearance of 1/16" between fixture and encoder.  This assembly allows the shaft to float and increases the lifetime of the bearings.  Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating.  Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW.  See datasheet for CW and CCW directions of the outputs.

Technical data for mount:  1/8" stainless steel wire

 
Dimensions


Hohner Automation Ltd. Tel: +44 (0) 1978 363-888
Whitegate Industrial Estate Fax: +44 (0) 1978 364-586
Wrexham LL13 8UG E-mail: uksales@hohner.com
United Kingdom Web: www.hohneronline.co.uk