|
|
|
|
Series 55 incremental hollow shaft encoder - 4 ... 20 mA output |
 |
5 | 5 | X | X | - | 0 | 3 | X | R | - | 0 | X | X | X | |||||||||||
|
Shaft Size |
Connection |
|
Resolution - ppr |
||||||||||||||||||||||
| 10 = 10 mm | 1 = 2m cable | ||||||||||||||||||||||||
| 12 = 12 mm | F = 4 pin plug | ||||||||||||||||||||||||
|
14 = 14 mm |
|||||||||||||||||||||||||
| 16 = 16 mm | |||||||||||||||||||||||||
| 20 = 20 mm | |||||||||||||||||||||||||
 |
|||||||||||||||||||||||||
Price: From £300.00
| Technical Data | Connection Options | |||||
| Operating temp: | - 20 ...+ 60 degrees C | 4 pin plug | Cable | |||
| - 4 ...+ 140 degrees F | + Loop A | 1 | White | |||
| Power supply: | 24V | - Loop A | 2 | Green | ||
| Weight: | 16 oz (0.45 kg) | + Loop B | 3 | Blue | ||
| Protection: | IP 64S, NEMA 3 | - Loop B | scn | Violet | ||
| Housing: | Die Cast Zinc Alloy |
|
||||
| Shaft: | Aluminum | |||||
| Bearings: | 2 x 61805 2RZ | |||||
| Torque: | 0.4 oz/in (3 N-cm) | |||||
| Humidity: | Up to 98% permissible |
Output |
||||
| Speed: | 2000 RPM max. | B is phased 90 degrees in front of A in cw direction | ||||
| Shock: | 10g (6msec) |
 |
||||
| Vibration: | 5g (500 Hz) | |||||
| Shaft load: | Radial / axial max 10 lbs | |||||
| Inertia: | 30 gm-cm2 | |||||
| Max. ppr | 512 | |||||
| Certifications |
|
Best suited to work with the following isolators: (can be purchased from us as well) Isolator Data Sheet [MTL5042] - DIN rail mounting - 158£ |
| IP 64S |
| SIRA Project Number 52 X 5980 |
| II 1G EEx ia II C T4 and/or I M1 EEx ia I |
| SIRA 00 ATEX 2126X [Certificate, Page 1, 2] PDF file |
| UL E216028 [Certificate] PDF file |
| Mounting Instructions |
|
Mount fixture to the encoder with three self-tapping no. 8 screws and three no. 8 washers. Slide the encoder onto the shaft. With the setscrew, tighten the hollow shaft onto the shaft. Mount the tether on the machine or motor-frame. The tether can be bent to adapt to any surface. This assembly allows the encoder to float and increases the lifetime of the bearings. Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating. Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW. See datasheet for CW and CCW directions of the outputs.
Technical data for tether: 0.3 mm stainless steel sheet
|
| Dimensions |
|
|
| Hohner Automation Ltd. | Tel: +44 (0) 1978 363-888 |
| Whitegate Industrial Estate | Fax: +44 (0) 1978 364-586 |
| Wrexham LL13 8UG | E-mail: uksales@hohner.com |
| United Kingdom | Web: www.hohneronline.co.uk |
