|
|
|
Series 08 incremental stainless steel encoder - 4...20 mA output |
|
|
0 | 8 | X | X | - | 0 | 3 | X | X | - | X | X | X | X | |||||||||||
|
Shaft Size |
Connection |
| |
|
Resolution - ppr |
|||||||||||||||||||||
| Hollow Shaft | 1 = 2 m cable | | | |||||||||||||||||||||||
| 08 = 8 mm | 2 = 5 m cable | | | |||||||||||||||||||||||
| 10 = 10 mm | F = 4 pin plug | | | |||||||||||||||||||||||
| 12 = 12 mm | | | ||||||||||||||||||||||||
| Solid Shaft (insert) | Housing Material | ||||||||||||||||||||||||
| K2 = 6 x 10 mm | S = Stainless Steel | ||||||||||||||||||||||||
| K4 = 10 x 20 mm | M = Blue Anodized Aluminum | ||||||||||||||||||||||||
| K5 = 12 x 20 mm |
|
||||||||||||||||||||||||
Price: From £290.00
| Technical Data | Connection Options | |||||
| Operating temp: | - 20 ...+ 60 degrees C | 3 + S | Cable | |||
| - 4 ...+ 140 degrees F | + Loop A | 1 | + Loop A | Red | ||
| Power Supply: | 24 Volts | - Loop A | 2 | - Loop A | Black | |
| Max frequency: | 5 kHz | + Loop B | 3 | + Loop B | White | |
| Weight: | 23 oz (0.75 kg) | - Loop B | scn | - Loop B | Green | |
| Protection: | IP 67M |  |
||||
| Housing: | Stainless Steel, Al | |||||
| Shaft: | Stainless Steel | |||||
| Bearings: | 3 x 6803 ZZ C2 | |||||
| Torque: | 0.7 oz/in (5 N-cm) | Output | ||||
| Shaft load: | Supports its own weight | B is phased 90 degrees in front of A in cw direction | ||||
| Humidity: | Up to 98% permissible |
 |
||||
| Speed: | 3000 RPM max. | |||||
| Max. ppr | 512 ppr | |||||
| Certifications |
|
Best suited to work with the following isolators: (can be purchased from us as well) Isolator Data Sheet [MTL5042] - DIN rail mounting - 131£ |
| IP 67M |
| SIRA Project Number 52 X 5980 |
| II 1G EEx ia II C T4 and/or I M1 EEx ia I |
| SIRA 00 ATEX 2126X [Certificate, Page 1, 2] PDF file |
| UL E216028 [Certificate] PDF file |
| Mounting Instructions |
|
Mount the tether on the machine or motor-frame. The tether can be bent to adapt to any surface. This assembly allows the encoder to float and increases the lifetime of the bearings. Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating. Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW. See datasheet for CW and CCW directions of the outputs.
Technical data for tether: 0.3 mm stainless steel sheet
|
| Dimensions |
|
|
| Hohner Automation Ltd. | Tel: +44 (0) 1978 363-888 |
| Whitegate Industrial Estate | Fax: +44 (0) 1978 364-586 |
| Wrexham LL13 8UG | E-mail: uksales@hohner.com |
| United Kingdom | Web: www.hohneronline.co.uk |
