Shaft Size
|___|
Resolution - bits
Output Code
16 = 16 mm
30 gray, 2 m cable
|
hohner |
Hohner Automation Ltd. |
| Home | Distributors | Terms | About Us | Accessories | Download 3D AutoCAD |
|
Series 14 absolute hollow shaft encoder parallel output |
|
|
1 | 4 | X | X | 2 | 0 | X | X | / | X | X | X | X | ||||||||||||
|
Shaft Size |
|
|___| |
|
Resolution - bits |
|||||||||||||||||||||
| 12 = 12 mm | | | 1024 = 10 bit | |||||||||||||||||||||||
| 14 = 14 mm |
Output Code |
4096 = 12 bit | |||||||||||||||||||||||
|
16 = 16 mm |
20 = binary, 16 pin | ||||||||||||||||||||||||
| 20 = 20 mm | 24 = gray, 16 pin | ||||||||||||||||||||||||
| 25 = 25 mm | 29 = binary, 2 m cable | ||||||||||||||||||||||||
| 40 = 40 mm |
30 gray, 2 m cable |
||||||||||||||||||||||||
| 1A = 1 inch | 31 = binary, 20 m cable | ||||||||||||||||||||||||
| 1B = 1 - 1/8 inch | 32 = gray, 20 m cable | ||||||||||||||||||||||||
| Technical Data | Connection Options | ||||
| Operating temp: | - 20 ...+ 60 degrees C | 16 pole | Cable | ||
| - 4 ...+ 140 degrees F | Power GND | 1 | Black | ||
| On request: | -20 ... + 100 degrees C | Power 11-24V | 2 | Red | |
| Power supply: | 11 - 24V | Channel 2-0 | 3 | White | |
| Current consumption: | 120 mA (max.) | Channel 2-1 | 4 | Blue | |
| Weight: | 21 oz (0.6 kg) | Channel 2-2 | 5 | Yellow | |
| Protection: | IP 64S, NEMA 3 | Channel 2-3 | 6 | Green | |
| Housing: | Aluminum | Channel 2-4 | 7 | Violet | |
| Shaft: | Aluminum | Channel 2-5 | 8 | Brown | |
| Bearings: | 2 x 6005 ZZ C2 | Channel 2-6 | 9 | Pink | |
| Torque: | 0.4 oz/in (3 N-cm) | Channel 2-7 | 10 | Turquoise | |
| Humidity: | Up to 98% permissible | Channel 2-8 | 11 | Grey | |
| Speed: | 600 RPM max. | Channel 2-9 | 12 | Orange | |
| Shock: | 10g (6msec) | Channel 2-10 | 13 | Red / Green | |
| Vibration: | 5g (500 Hz) | Channel 2-11 | 14 | Red / Blue | |
| Shaft load: | Supports its own weight | For cw | NC on 16 | Red / Black or Yellow NC | |
| For ccw | 16 to GND | Red / Black or Yellow to GND | |||
| Output | |||||
 |
|||||
| Count will increment in cw direction | |||||
| Mounting Instructions |
|
Mount fixture to the
machine with three screws and three washers, M6 or 1/4". Slide the encoder
onto the shaft. With the setscrews, tighten the hollow shaft encoder onto
the shaft with a minimum clearance of 1/16" between fixture and encoder.
This assembly allows the shaft to float and increases the lifetime of the
bearings. Connect the encoder as per wiring specifications. Make sure
power supply is within the proper voltage and current rating. Encoder can
be mounted with the setscrew on the machine side or on the opposite side for
either CW or CCW. See datasheet for CW and CCW directions of the outputs.
Technical data for mount: 1/8" stainless steel wire |
| Dimensions |
|
|
| Hohner Automation Ltd. | Tel: +44 (0) 1978 363-888 |
| Whitegate Industrial Estate | Fax: +44 (0) 1978 364-586 |
| Wrexham LL13 8UG | E-mail: uksales@hohner.com |
| United Kingdom | Web: www.hohneronline.co.uk |
