| F | P | X | X | - | 3 | 3 | X | X | - | X | X | X | X | |||||||||
| |___| | | |
| |
Resolution |
|||||||||||||||||||
| | |
IP rating |
Connection | ||||||||||||||||||||
| Shaft Size | 4 = IP67 | 0 = DeviceNet Cable | ||||||||||||||||||||
| A1 = 1" | 4 = 5 pin micro | |||||||||||||||||||||
| 25 = 25 mm | ||||||||||||||||||||||
| 30 = 30 mm | ||||||||||||||||||||||
|
hohner |
Hohner Corporation |
| Home | Distributors | Terms | About Us | Accessories | Download 3D AutoCAD |
|
Series FPX Incremental DeviceNet Encoder |
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Technical Data | Encoder Description | |||
| Operating temp: | - 20 ...+ 60 degree C | An incremental encoder is coupled to a 32 bit built in counter | ||
| - 04 ...+ 140 degree F | Value is measured in counts between 0 and 4 294 967 295 | |||
| On request | - 20 .. +100 degree C | DeviceNet Service - reset code 05 will reset the counter to 0 | ||
| Current consumption: | 80 mA (max.) | |||
| 6 ft drop cable | Device Configuration | |||
| Weight: | 53oz (1.50 kg) | ODVA profile: | Resolver | |
| Protection: | IP 66 | Explicit Peer to Peer Messaging | Not supported | |
| Housing: | Aluminum | I / O Peer to Peer Messaging | Not supported | |
| Shaft: | Stainless Steel | Configuration consistency value | Not supported | |
| Bearings: | Ball Races | Faulted node recovery | Not supported | |
| Torque: | 0.4 oz/in (3 N-cm) | Baud rate | Supported | |
| Humidity: | Up to 98% permissible | Master / Scanner | Not supported | |
| Speed: | 3000 RPM max. | I / O Slave messaging | Not supported | |
| Directions | Numbers rising in cw direction | Bit strobe | Not supported | |
| Poll | Supported | |||
| Standards | Cyclic | Not supported | ||
| UL file number - 198887 | Change of state | Not supported | ||
| European standard EN 50324 | EDS | |||
| Tested by University of Michigan | Vendor | ID 34 | ||
 |
Devicetype | 9 | ||
| Product code | 2 | |||
| Product name | MTDR | |||
| Catalog | 32 bit incremental encoder | |||
| Expected response data | 4 bytes | |||
| Maximum value | 32 bit | |||
| Mounting Instructions |
|
Mount fixture to the encoder with three M3 screws. Slide the encoder onto the shaft. With the setscrew, tighten the hollow shaft onto the shaft. Mount the tether on the machine or motor-frame. The tether can be bent to adapt to any surface. This assembly allows the encoder to float and increases the lifetime of the bearings. Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating. Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW. See datasheet for CW and CCW directions of the outputs.
Technical data for tether: 0.3 mm stainless steel sheet |
| Dimensions |
|
|
| Hohner Corp. | Tel: (905) 563 4924 |
| 5536 Regional Road 81 | Fax: (905) 563 7209 |
| Beamsville, Ontario | E-mail: hohner@hohner.com |
| Canada L0R 1B3 | Web: www.encoderonline.com |
