| 8 | 8 | X | X | - | 3 | 3 | X | X | - | A | 0 | 1 | 2 | |||||||||
| |___| | | |
| |
||||||||||||||||||||
| | |
IP rating |
Connection | ||||||||||||||||||||
| Shaft Size | 0 = IP54 | 0 = DeviceNet Cable | ||||||||||||||||||||
|
07 = 1" with 1/4" keyway |
4 = 5 pin micro | |||||||||||||||||||||
| 17 = 30 mm | ||||||||||||||||||||||
| 03 = 1/2" | ||||||||||||||||||||||
| 16 = 24 mm | ||||||||||||||||||||||
| 25 = 1 - 1/4" | ||||||||||||||||||||||
| 05 = 5/8" with 3/16" keyway | ||||||||||||||||||||||
|
hohner |
Hohner Corporation |
| Home | Distributors | Terms | About Us | Accessories | Download 3D AutoCAD |
|
Series 88 Absolute DeviceNet Encoder |
|
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Technical Data | Encoder Description | |||
| Operating temp: | - 20 ...+ 60 degree C | The 12 bit absolute encoder has a 12 bit binary value | ||
| - 04 ...+ 140 degree F | ||||
| On request | - 20 .. +100 degree C | |||
| Current consumption: | 80 mA (max.) | |||
| 6 ft drop cable | Device Configuration | |||
| Weight: | 38.5oz (1.1 kg) | ODVA profile: | Resolver | |
| Protection: | IP 54 | Explicit Peer to Peer Messaging | Not supported | |
| Housing: | Die Cast Zinc Alloy | I / O Peer to Peer Messaging | Not supported | |
| Shaft: | Aluminum | Configuration consistency value | Not supported | |
| Bearings: | 2 x 6008 ZZ C2 | Faulted node recovery | Not supported | |
| Torque: | 0.4 oz/in (3 N-cm) | Baud rate | Supported | |
| Humidity: | Up to 98% permissible | Master / Scanner | Not supported | |
| Speed: | 3000 RPM max. | I / O Slave messaging | Not supported | |
| Directions | Numbers rising in cw direction | Bit strobe | Not supported | |
| Poll | Supported | |||
| Standards | Cyclic | Not supported | ||
| UL file number - 198887 | Change of state | Not supported | ||
| European standard EN 50324 | EDS | |||
| Tested by University of Michigan | Vendor | ID 34 | ||
 |
Devicetype | 9 | ||
| Product code | 1 | |||
| Product name | MTDR | |||
| Catalog | 12 bit absolute encoder | |||
| Expected response data | 4 bytes | |||
| Maximum value | 12 bit | |||
| Mounting Instructions |
| Mount fixture to the
machine with three screws and three washers, M6 or 1/4". Slide the encoder
onto the shaft. With the setscrews, tighten the hollow shaft encoder onto
the shaft with a minimum clearance of 1/16" between fixture and encoder.
This assembly allows the shaft to float and increases the lifetime of the
bearings. Connect the encoder as per wiring specifications. Make sure power supply is within the proper voltage and current rating. Encoder can be mounted with the setscrew on the machine side or on the opposite side for either CW or CCW. See datasheet for CW and CCW directions of the outputs. Technical data for mount: 1/8" stainless steel wire |
| Dimensions |
|
|
| Hohner Corp. | Tel: (905) 563 4924 |
| 5536 Regional Road 81 | Fax: (905) 563 7209 |
| Beamsville, Ontario | E-mail: hohner@hohner.com |
| Canada L0R 1B3 | Web: www.encoderonline.com |
